A tear along the drawn edge of a door panel, or a series of wrinkles along the edge, often originates before the sheet metal even enters the die. One of the less controlled factors is lubrication, the stage in which oil is applied to coils and blanks: the distribution of the film determines how the material slides between the punch and die. With the dimensional tolerances and production rates typical of automotive component stamping, even small irregularities can result in rejected parts. An automotive lubrication system must therefore be evaluated with the same level of rigour applied to the press and the die.
Selective Application in Automotive Lubrication Systems
The amount of oil deposited on the sheet metal is measured in grams per square metre and largely determines the friction between the material and the die surfaces. A film that is too thin restricts the sheet metal’s movement towards the cavity and promotes localised thinning that can eventually lead to tearing. Conversely, too much lubricant allows the material to slide too easily under the blank holder, producing wrinkles and making the geometry of the part unstable. Between these two extremes lies a narrow operating window, and an automotive lubrication system must maintain the set grammage in every zone throughout the entire production shift.
Advanced high-strength steels, which are increasingly used in structural components, further narrow this window: they offer lower formability and generate high contact pressures, increasing the risk of galling. Aluminium, also used for hoods and doors, is similarly sensitive to changes in friction and tends to cause material transfer onto the tooling.
A stamped part rarely requires the same amount of lubrication at every point. Areas subject to deep drawing, such as wheel-arch edges or the corners of an inner door panel, require more oil than flat areas, where the material undergoes relatively limited deformation. Zoned lubrication addresses this difference by dividing the blank surface into sectors and assigning a specific quantity to each one, ensuring that every zone receives the grammage suited to the expected deformation. The result is oil consumption proportional to the actual requirement and a more uniform distribution of deformation from one part to the next.
Residual Oil and Downstream Press Operations
After stamping, oil remains on the part throughout the production cycle and reaches the body shop, where components are assembled into the vehicle body. The amount of oil remaining on the surface can therefore affect processes that take place hours later, sometimes in different production areas. An apparently harmless excess of oil during pressing can generate defects that are difficult to trace back to their original cause. Four processes are particularly sensitive:
- Spot welding, where a thick oil film alters the contact resistance between the sheets, contaminates the electrodes and shortens dressing intervals;
- Structural bonding, because epoxy adhesives tolerate only a limited amount of oil on the surface before losing adhesion;
- Sealing, as sealants applied to excessively oily surfaces tend to slide or detach during curing;
- Degreasing and cathodic electrocoating, where excess oil saturates washing baths more quickly and can leave areas uncoated, creating the conditions for future corrosion.
How the oil reaches the sheet metal also matters. Poorly controlled spraying disperses part of the lubricant into the air as an oil mist, which settles on presses, conveyors and floors. The mist also removes a variable amount of lubricant from the part, meaning that the actual grammage can differ from the programmed value. Deposits create slippery surfaces in walkways, contaminate optical sensors used to detect blank positioning and worsen air quality for people working on the production line.
In the automotive sector, an effective lubrication system must therefore contain spraying within enclosed spray heads and extract oil mist at the source, before it can escape from the machine.
Process Repeatability and Control
An automotive stamping line processes numerous part numbers, each with its own material, thickness and geometry. Every production change requires the lubrication system to be returned to the validated conditions for that specific part, while relying solely on operator experience introduces variability from one shift to another. The safer approach is to save the parameters in a recipe associated with each part number, which can be recalled from the control panel within seconds. The first part produced after a die change can then be manufactured with the correct lubrication settings, without adjustment trials that waste sheet metal and machine time.
Managing multiple oils introduces an additional requirement. Steel and aluminium often require lubricants with different viscosities and formulations, and switching between them leaves residues in tanks, pipes and valves. Without a cleaning cycle, the previous oil contaminates the new one and alters its behaviour in the die.
Continuous system monitoring is also essential. A partially blocked nozzle or a valve that fails to open can leave an area of the blank without oil, with the defect only becoming apparent during quality inspection, after hundreds of parts have already been produced. Diagnostics that detect dispensing anomalies in real time turn a quality issue into an actionable in-line alert.
Dietronic’s Sagoma system addresses these requirements with zoned spray lubrication that divides the blank into 50 × 50 mm squares and assigns up to 8 different quantities to each one. The touchscreen control panel stores recipes and integrates diagnostics and automatic adjustment, while the multi-oil management system includes an automatic cleaning procedure. Enclosed spray heads with patented modular manifolds, combined with integrated extraction, keep oil mist contained within the machine.
Visit the Sagoma page to assess whether the system is suitable for your production line. If you are interested, contact the Dietronic technical team at sales@dietronic.eu.
